Product Details:
Usage/Application | Fabric |
Capacity | up to 200KN |
Material | ALL |
Display Type | Computerized |
Brand | KMI |
Operating Mode | Automatic |
Accuracy | +/-1% As per IS 1828 |
Number Of Load Cells | TWO |
Number Of Screws | TWO |
Resolution | 4000 counts in each range |
Accuracy | +/- 1% AS per IS1828 |
Brand | KMI |
Material for Construction | MS,SS,others |
Power Source | Electric |
Computer control fabric tensile testing Equipment
1. Machine.
Computer controlled equipment to test tensile strength and elongation of a wide range of materials. Compression, Bending,Flexural, Shearing Peeling, Tear & other tests are possible through special grips & fixtures.
2. Force Measurement.
By Electronic Load Cells of high accuracy. Two Load-cells are included, One each for higher and lower strength material.
3. Elongation Measuring Device.
Built-in Device.Measurement through cross - head movement by incremental encoder. For range & resolution,refer specification table.
4. Batch Test Facility.
For a Batch test - can furnish statistical analysis report in regard to minimum, maximum, mean and C.V% of strength and elongation.
5. Cyclic Test Facility.
Particularly Suitable For rubber belting .Automatic loading and unloading of specimen for desired number of cycles.( Maximum 999 cycles) Specimen can be stretched between given load or elongation limit - with 5% tolerance.
6. Proof Test Facility.
Direct indication of proof load at selectable percentage of specimen gauge length.
7. Measuring Unit.
Force Value Display in gm & kgf and print-out in selectable unit - gm, kg, N, cN, kN Or Lbs.
Elongation. Display in mm and printout in mm or Inch.
8. Test Result.
Display. During test all relevant test data including Load - Elongation Curve displayed on Computer screen. Print-out Test Report with Load - Elongation Curve can be had on completion of test .
9. Graph.
Load v/s Elongation & Stress V/S strain graphs. Auto scaling before print out. Special graph against specific need can be provided.
For desired force value , corresponding elongation value & vice-versa can be directly seen on screen.
10. Cross-head Drive & Speeds.
Variable test speed through variable frequency A.C.Drive.
For speed range refer table. Speed selection through computer key board.
Other speeds can be offered, On cost basis against specific requirement
11.Testing Lower Strength Materials.
For testing lower strength material additional load-cell can be provided on cost basis.
12. Protections.
Overload & Over travel protection. Automatic stopping on specimen ruptures.
13. Accuracy.
+ 1% of the verification load OR + 0.2% of rated capacity of range employed, which-ever is greater. Complying IS 1828 ( part 1) : 1991 /ISO 7500 – 1 : 1986
Product Details:
Machine Type | computerized Universal testing machine utm |
Model Name/Number | 201T |
Usage/Application | ALL |
Automation Grade | Automatic |
Driving Method | Gear ,motor |
Accuracy | +/-1% As per IS 1828 |
Brand | KMI,KMI |
Capacity | Upto 200 KN |
Power Source | Electric |
Material for Construction | MS,SS,Others |
1) Facility to have multiple numbers of load cells thus giving wide range of coverage with better accuracy at higher and lower load ranges with minimum resolutions (least count).
2)Special facility for mounting additional load cells as a result of which there is no need to change either load cells or grips on the machine.
3) Speed of the machine can be regulated through computerized systems.
4) Unlimited storage facility of records files with an option of custom built software which can be supplied at extra costProduct Details:
Usage/Application | ALL |
Material | ALL |
Phase | Single |
Brand | KMI |
Operating Mode | Automatic |
Display Type | computer |
Model Name/Number | Two |
Number Of Load Cells | Two |
Number Of Screws | Two |
Capacity | 50 kN |
Material for Construction | MS,SS,Others |
Accuracy | +/- 1% |
Brand | KMI |
Electronic Material Tensile Tester by KMI
We are manufacturing and supplying high precision testing machine that are used for determining tensile strength and elongation of textile, rubber, plastic, cables and conductors, leather, asbestos, paper, plywood, metal, and other material. It can test material in conformity with IS or other standard. We are pioneer in the manufacturing of tensile testing machine in India , that is used for accurate testing results.
The range includes :
Computerized Universal Testing Machine with Hydraulic Straining Unit.
Micro Processor based version is also available.
Features:
High Quality
Competitive Price
More than 10000 satisfied clients
Product Details:
Minimum Order Quantity | 1 Set |
Usage/Application | Industrial |
Display Type | Computerized |
Model Name/Number | 201T |
Capacity | Upto 100 KN,Up to 200KN |
Material | ALL |
Automation Grade | Automatic |
Operating Mode | Automatic |
Phase | Single |
Number Of Load Cells | TWO |
Brand | kmi,KMI |
Number Of Screws | TWO |
Resolution | 4000 count of each ranges |
Driving Method | Gears,Motor |
Accuracy | +/-1% As per IS 1828 |
Place Of Origin | INDIA |
Finer load resolution | 4000 counts |
Power Source | Electric |
We are offering Computerized Testing Version Machine. This is a sophisticated computerized version. Have all features of Microprocessor based equipment.
Advanced features:
Additional Information:
Product Details:
Minimum Order Quantity | 1 Set |
Machine Type | UTM |
Brand | KMI |
Driving Method | Gear,Motor |
Control | Computerized |
Material | ALL |
Capacity | Upto 10 KN |
Accuracy | +/- 1% As per IS 1828 |
Material for Construction | MS,SS,Others |
Brand | KMI |
Our extensive and quality range includes sophisticated Computerized Testing Equipment like computerized fabric and Lea tester, that have all the features of microprocessor based version. Further, it has variable speed A.C drive, permanent data storage facility and fine load resolution that 4000 counts for each measuring range.
Some of its other features are as follows:
Count information can be directly received from count balance or through key board
Additional Information:
Product Details:
Machine Type | UTM |
Brand | KMI |
Driving Method | Gear,Motor |
Capacity | Up To 20KN |
Control | Computerized |
Accuracy | +/- 1% AS Per IS 1828 |
Brand | KMI |
Power Source | Electric |
Material for Construction | MS,SS,others |
1. Machine.
Computer controlled equipment to test tensile strength and elongation of a wide range of materials. Compression, Bending,Flexural, Shearing Peeling, Tear & other tests are possible through special grips & fixtures.
2. Force Measurement.
By Electronic Load Cells of high accuracy. Two Load-cells are included, One each for higher and lower strength material.
3. Elongation Measuring Device.
Built-in Device.Measurement through cross - head movement by incremental encoder. For range & resolution,refer specification table.
4. Batch Test Facility.
For a Batch test - can furnish statistical analysis report in regard to minimum, maximum, mean and C.V% of strength and elongation.
5. Cyclic Test Facility.
Particularly Suitable For rubber belting .Automatic loading and unloading of specimen for desired number of cycles.( Maximum 999 cycles) Specimen can be stretched between given load or elongation limit - with 5% tolerance.
6. Proof Test Facility.
Direct indication of proof load at selectable percentage of specimen gauge length.
7. Measuring Unit.
Force Value Display in gm & kgf and print-out in selectable unit - gm, kg, N, cN, kN Or Lbs.
Elongation. Display in mm and printout in mm or Inch.
8. Test Result.
Display. During test all relevant test data including Load - Elongation Curve displayed on Computer screen. Print-out Test Report with Load - Elongation Curve can be had on completion of test .
9. Graph.
Load v/s Elongation & Stress V/S strain graphs. Auto scaling before print out. Special graph against specific need can be provided.
For desired force value , corresponding elongation value & vice-versa can be directly seen on screen.
10. Cross-head Drive & Speeds.
Variable test speed through variable frequency A.C.Drive.
For speed range refer table. Speed selection through computer key board.
Other speeds can be offered, On cost basis against specific requirement
11.Testing Lower Strength Materials.
For testing lower strength material additional load-cell can be provided on cost basis.
12. Protections.
Overload & Over travel protection. Automatic stopping on specimen ruptures.
13. Accuracy.
+ 1% of the verification load OR + 0.2% of rated capacity of range employed, which-ever is greater. Complying IS 1828 ( part 1) : 1991 /ISO 7500 – 1 : 1986
Product Details:
Usage/Application | ALL |
Material | ALL |
Phase | Single |
Operating Mode | Automatic |
Display Type | Computerized |
Model Name/Number | 201T |
Number Of Load Cells | TWO |
Number Of Screws | TWo |
Capacity | 10N to 200kN |
Model | 201t |
Power Source | Electric |
Brand | kmi |
Computer Support | Available |
We are able to gain immense expertise in delivering Computerized Tensile Testing Machine to our clients. The offered range of computerized tensile testing machines is made utilizing high grade raw material and innovative technology in complete adherence with the international quality standards. Along with this, the offered range of computerized tensile testing machines is suitably checked on different characteristics to maintain its authenticity throughout the designing procedure.
Features:
High tensile strength
Durable finish standards
Reliable performance.
Product Details:
Minimum Order Quantity | 1 Piece |
Crosshead Return Speed | 500mm/min |
Test Width (mm) Approx. | 100mm |
Effective Stroke (mm) Approx. | 600mm |
Max. Capacity | 50 kN |
Crosshead Travel (mm) Approx. | 700mm |
Crosshead Speed (mm/min) | 50 to 500mm/min |
Tensile Load Measurement Accuracy | - + 1 Of Load Or 0.2% Of Full Scale Whichever Is Higher |
Additional Information:
Product Details:
Minimum Order Quantity | 1 Piece |
Stroke Limiter Upper/lower | Provided |
Max. Capacity | 50kn |
Test Width (mm) Approx. | 100mm |
Crosshead Travel (mm) Approx. | 700mm |
Effective Stroke (mm) Approx. | 600mm |
Crosshead Speed (mm/min) | 50 To 500mm/min |
Crosshead Return Speed | 500mm/min |
Tensile Load Measurement Accuracy | - /+ 1 Of Load Or 0.2% Of Full Scale Whichever Is Higher. |
Power | 3 Hp |
We are able to gain immense expertise in delivering Computerized Material Testing Equipment to our clients. The offered range of computerized tensile testing machines is made utilizing high grade raw material and innovative technology in complete adherence with the international quality standards.
Additional Information:
Product Details:
Minimum Order Quantity | 1 Set |
Usage/Application | ALL |
Material | ALL |
Display Type | Computerized |
Brand | KMI |
Operating Mode | Automatic |
Number Of Load Cells | TWo |
Number Of Screws | TWo |
Resolution | 4000 counts in each range |
Accuracy | +/- 1 % |
Material for Construction | Stainless steel |
Capacity | 50 KN |
Brand | kmi |
Computerized Tensile Tester Specification
1. Machine
Computer controlled equipment to test tensile strength and elongation of a wide range of materials. Compression, Bending,Flexural, Shearing Peeling, Tear & other tests are possible through special grips & fixtures.
2. Force Measurement
By Electronic Load Cells of high accuracy. Two Load-cells are included, One each for higher and lower strength material.
3. Elongation Measuring Device.
Built-in Device.Measurement through cross - head movement by incremental encoder.For range & resolution,refer specification table.
4. Batch Test Facility.
For a Batch test - can furnish statistical analysis report in regard to minimum, maximum, mean and C.V% of strength and elongation.
5. Cyclic Test Facility.
Particularly Suitable For rubber belting .Automatic loading and unloading of specimen for desired number of cycles.( Maximum 999 cycles) Specimen can be stretched between given load or elongation limit - with 5% tolerance.
6. Proof Test Facility.
Direct indication of proof load at selectable percentage of specimen gauge length.
7. Measuring Unit.
Force Value Display in gm & kgf and print-out in selectable unit - gm, kg, N, cN, kN Or Lbs.
Elongation. Display in mm and printout in mm or Inch.
8. Test Result.
Display. During test all relevant test data including Load - Elongation Curve displayed on Computer screen. Print-out Test Report with Load - Elongation Curve can be had on completion of test .
9. Graph.
Load v/s Elongation & Stress V/S strain graphs. Auto scaling before print out. Special graph against specific need can be provided.
For desired force value , corresponding elongation value & vice-versa can be directly seen on screen.
10. Cross-head Drive & Speeds.
Variable test speed through variable frequency A.C.Drive.
For speed range refer table. Speed selection through computer key board.
Other speeds can be offered, On cost basis against specific requirement
11.Testing Lower Strength Materials.
For testing lower strength material additional load-cell can be provided on cost basis.
12. Protections.
Overload & Over travel protection. Automatic stopping on specimen ruptures.
13. Accuracy.
+ 1% of the verification load OR + 0.2% of rated capacity of range employed, which-ever is greater. Complying IS 1828 ( part 1) : 1991 /ISO 7500 – 1 : 1986
Additional Information:
Product Details:
Usage/Application | ALL |
Capacity | Up To 100Kn |
Material | ALl |
Display Type | Computerized |
Brand | KMI |
Operating Mode | Automatic |
Accuracy | +/- 1% As+ per IS 1828 |
Number Of Load Cells | TWO |
Number Of Screws | TWO |
Brand | KMI |
Material Grade | MS,SS,Others |
Accuracy | +/- 1% As+ per IS 1828 |
Input Voltage | 220 V / 50 Hz |
Computer Support | Available |
Product Details:
Model Name/Number | 201T |
Capacity | 10KN |
Material | ALL |
Automation Grade | Automatic |
Phase | Single |
Brand | KMI |
Driving Method | Gear,Motor |
Accuracy | +/-1% As per IS 1828 |
Capacity | upto 10 KN |
Brand | KMI |
Material for Construction | MS,SS,Others |
Power Source | Electric |
Accuracy | +/- 0.1% As per IS 1828 |
Product Details:
Usage/Application | Lea Testing |
Material | Textile |
Traverse Speed | 30mm/min to 300mm/min |
Power | Single Phase |
Resolution | 4000 counts in each range |
Accuracy | +/- 1% AS per IS 1828 |
Model Name/Number | 201T |
Grip Separation | Up to 900MM |
Finer load resolution | 4000 counts for each measuring range |
Capacity | Up to 10 KN |
Brand | KMI |